本价22.5元/只是执行批发，50只起批。50只内请勿再议价。
不零售

一、功能特点
1.一体化设计，喇叭与主机结合在一起。
2.采用工业级IC，抗干扰能力强。
3.六音环绕报警音源,声音不让人厌烦。
4.遥控调节震动灵敏度，方便不同场所使用。
5.超长距离遥控。
6.内置高灵敏度震动传感器，配合人性化软件设计。
7.具有强制开锁报警功能。 8.声音辩别布防/撤防状态。
二、贴心提示
1、遥控器比较精密，请勿重摔或浸水。
2、当发现遥控距离减短或遥控器指示灯变暗，请更换电池。
3、非人为故障，实行一年免费保修，请与当地经销商联系。
三、电气特征
工作电压：36V/48V通用。
静态电流：8mA左右。
报警声音响度：120dB左右。
遥控器发射频率：315MHz。
遥控距离：100米左右（开阔地，配拉杆天线遥控器）。
四、接键说明 

五、接线说明 

六、操作说明
1、布防状态：短按一下“布防键”，喇叭响一声，六秒后进入警戒状态。首次震动触发，喇叭鸣响5秒以示警告，再次受到震动，则喇叭连续鸣响15秒，重新上电后仍为布防状态。
2、撤防状态：短按一下“撤防键”，喇叭响二声，主机立即退出防盗警戒状态。此时机车受到任何震动撞击和开锁都不会发出警报声,重新上电后仍为撤防状态。
3、紧急求助/寻车状态：任何状态下,短按“紧急求助/寻车键”主机马上发出12秒警报声，告知车主机车所在位置，同时起吓阻和紧急求助作，按遥控器任意键警报声停止。
4、遥控调节振动灵敏度：在撤防状态下长按住“紧急求助/寻车键”5秒便可听到灵敏度调节声，单片机会自动确认并记忆当前灵敏度的级数,具有调电保护功能。 A档:Bi一声灵敏度最高。 B档:BiBi二声灵敏度中高。 C档:BiBiBi三声灵敏度中低。 D档:BiBiBiBi四声灵敏度最低。 　 七、怎样配对遥控器
1、学习对码方法: 用螺丝刀打开主机后,在通电的状态下，长按住学习按键大约3秒钟后, 学习指示灯亮，松开按键，然后按无线遥控器中的任何一个键，这时指示灯立刻灭掉，既表示学习对码成功。再次学习遥控器的时候重新按照以上的操作即可。
2、删除遥控器的方法：长按住学习键5秒钟左右，学习指示灯亮了以后，会闪烁3次后，以前学习的遥控器都会被删掉。 　
八、9965摩托车 电动车震动感应器接线图 

九、强制开锁警戒功能简介 在布防状态下,当有撬锁或拧动机车钥匙时锁头检测线会检测到高电平,主机就会发出12秒的警报声。
十、使用流程
1、接上电源正，负极。
2、接好锁头检测线。
3、按遥控器各功能按键检查是否正常。
4、检查震动和锁头检测线是否能正常工作。
5、找一个位置用泡棉贴好主机（注意防水）。 　
十一、产品标准配置 主机1台，无线遥控器1个，导线1组，中英文说明书1本。
9965 Vibrative Inductors
for Motorbike and Electric vehicle
★ Main function and characteristic
1.Integrative design, hang the speaker and the mainframe together.
2.Adopt industry level IC, have strong capability of anti-jamming.
3.Have six rounding alarm sound fountain, never be fed up with it.
4.Vibrative remote control is very sensitive, convenient to be used in different places.
5.Control around quite a long distance.
6.High sensitive vibrate sensor inside, have humanity software design.
7.Be provided with alarm function when the lock is opened by force. 
8.Have different sounds in disposing safety and retracting safety.
★Warning to remote control
1.The remote control has high precision, please don’t throw it heavily or leave it in the water.  
2.Please change the battery when you find the distance of controlling becomes shorter or the indicator light turns dark.
3.Not man-made trouble, we guarantee to keep it in good repair for free for  one year 
★Electric Characteristics
Working Voltage: 36V/ 48V 
Static state electric current: Around 8mA
Sonority of alarm: Around 120dB
Frequency of eradiating: 315MHz
In widen place, Around 100m. (for the remote antenna.)
★Meets the key explanation
                                  
★Wiring explanation
 
★The operation explained
1．State of disposing safety: Press the button for disposing safety, go into the guarding state in six seconds after the speaker sounds for one time. 
2．State of retracting safety: Press the button of retracting safety, the mainframe will retreat form the guarding state immediately after the speaker sounds for two times. Then it will not sound when the vehicle is shaked, striked or the lock is prized, will keep the state of retracting safety when it is offered power again .
3．State of seeking emergent help or looking for vehicle: At any state, press the button of seeking help or looking for vehicle, the mainframe will utter alarm sound for 12 seconds.
4．Control the sensitive degree remotely: Press the button of seeking emergent help or looking for vehicle for five seconds, at the state of retracting safety, then can hear the sound of controlling the sensitive degree, singlechip will affirm and record the sensitive degree currently, have protecting function of regulating electricity.   
A.degree: Bi (one time) stands for the highest sensitive degree
B.degree: BiBi (two times) stands for the higher sensitive degree
C.degree: BiBiBi(three times) stands for the lower sensitive degree
D.degree: BiBiBiBi(four times) stands for the lowest sensitive degree
★How to arrange the mainframe and the remote control in pairs
1．Method of learning: Open the mainframe with a screwdriver, press the Learning button for about three seconds at the electrifying state, the learning indicator light will shine, loosen the button, then press the any button of the remote control, the indicator light will be off, that means you have learned successfully. Follow the steps above will learn again.
2．Method deleting remote control: Press the learning button for about five seconds, learning indicator light will shine ,then it will flash three times, that means have been deleted.
★wiring diagram of 9965  Vibrative Inductors for Motorbike and Electric vehicle

★Brief introduction of alarm function when the lock is opened by force.At the state of disposing safety, when the lock is prized or the key is wringed, the inspecting wire on the lock will inspect high electricity, the mainframe will utter alarm sound for 12 seconds.

★Procedure for using

1．Connect BAT+ and BAT-.
2．Connect the inspecting wire on the lock.
3．Check all the buttons to insure they can work.
4．Check vibrative mode and the inspecting wire to insure they can work.
5．Stick the mainframe at a proper place.
★Standard configuration of products
1 mainframe, 1 wireless remote control, 1 group of lead, 1 Chinese and English introduction。